EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . Temperature controller. EKC MAKING MODERN LIVING POSSIBLE Sensors: Danfoss Pt, PTC or NTC • Calibration of sensors. RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D.

Author: Mokazahn Taubar
Country: Fiji
Language: English (Spanish)
Genre: Love
Published (Last): 23 February 2014
Pages: 102
PDF File Size: 5.3 Mb
ePub File Size: 5.98 Mb
ISBN: 547-8-93052-878-4
Downloads: 19821
Price: Free* [*Free Regsitration Required]
Uploader: Mazujora

The Danfoss controller is used for applications where temperature is critical. A pulse signal starts the defrost Refrigeration control with two compressors The two compressors must be of the canfoss size.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102A 084B8500 for Freezer

The function is not active during a defrost or start-up after a defrost. Fitting the EKC controller with a plug-in module for communication gives access to all parameters of the 1002.

Push the upper or the lower button and select the new value 5. Start-up After a power cut the system can be started with a defrost. Fan cut in during defrost Here you can set whether 1002 is to operate during defrost. Refrigeration stopped by thermostat S Operating status The controller goes through some regulating situations where it is just waiting for the next point of the regulation. When the defrost starts the defrost timers are set at zero.

When the compressor is stopped, it must remain stopped for at least x minutes. None, defrost is based on time EKC A: Sensors Sair is thermostat sensors. When the value is passed, a defrost will start. The sensor is placed in the cold air flow after the evaporator or in the warm air flow just before the evaporator.

  APPSC ASO NOTIFICATION 2012 SYLLABUS PDF

Defrost in progress S Hermetic Compressors c02 min. Notify me about a product availability. All the mentioned methods can be used at random — if just one them is activated a defrost will be started. A measurement of the defrost temperature can be obtained directly through the use of an S5 sensor.

This also applies to ejc already on order provided that such alternations can be made without subsequential changes being necessary eoc specifications already agreed. There are two kinds of error reports – it can either be an alarm occurring during the daily operation, or there may be a defect in the installation.

The possible functions are described in menu o No stress and worry Thanks to the integration with cheap returns you can purchase without stress and be sure that the return process will be hassle free. Gold plating Cable length ranfoss be max. With only two keys, all functions can be set and programmed.

Controller for temperature control – EKC Manual |

A special moulding technique unites the hard front plastic, the softer buttons and the seal, so that they become an integral part of danfkss front panel. An A alarm will not be visible as long as there is an active E alarm. Drip-off time Here you set the time that dajfoss to elapse from a defrost and until danfss compressor is to start again. None, no sensor is connected 1: Providing personal data is voluntary, but necessary for providing a reply. EKC D Controller with three relay outputs, two temperature sensors and digital input.

  DESIGN OF OGEE SPILLWAY PDF

ON-time in minutes Min. All other outputs are Off. Refrigeration stopped, fan continues or stops as defined in F Copying still going on The information can be found in o65 or o66 a couple of seconds after copying has been started. After two seconds you can move into the menu again and check whether the copying was satisfactory.

To avoid a too high ranfoss of the setpoint, the max. Digital input Can be used for the following functions: There are no openings that can receive moisture or dirt. Find the parameter code you want to change and push the middle buttons until value for the parameter is shown. The function is defined in o This view will continue up till 15 min. Here you emc set the time delay. Activation can take place via r39 or input DI Alarm The controller can give alarm in different situations.

Push the uppermost or lowermost button to scan the rolling stack. The function is started with a pulse pressure. It’s a community-based project which helps to repair anything.

There is no temperature monitoring during case cleaning. A-alarms will not become visible until the set time delay has expired.