Go to the Web for instructions, No. Yes. Yes. No. Installation Guide. Install the server in the rack, if required. xSeries View and Download IBM Xseries maintenance manual online. Xseries Server pdf manual download. This manual provides information about installing the IBM® Remote Supervisor . v IBM Remote Supervisor Adapter User’s Guide . xSeries Type

Author: Kajinris Daikasa
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: History
Published (Last): 13 October 2013
Pages: 10
PDF File Size: 6.34 Mb
ePub File Size: 14.30 Mb
ISBN: 972-6-80191-596-2
Downloads: 23633
Price: Free* [*Free Regsitration Required]
Uploader: Shasar

Remove or disconnect the following devices one at a time until you find the failure turn on the server and reconfigure each time: Diagnostic tools overview The following tools are available to help you identify and resolve hardware-related problems: Don’t show me this message again.

Faites-vous aider pour soulever ce produit. Removing The Cover And Bezel Removing the cover and bezel The following illustration shows how to remove the cover and bezel. To change the configuration, janual Modify arrays. Complete the following steps to remove the PCI riser-card assembly from mxnual server. For a list of supported options for your server, go to http: Page 58 Table 7 describes the function for each switch on the switch block.

IBM Xseries 345 8670 Maintenance Manual

Cover-release latch Bezel Complete the following steps to remove the server top cover: If the ServeRAID Manager program detects an unconfigured controller and ready drives, the program automatically starts the Configuration wizard, and a window similar to jbm shown in Figure 1 opens. Set the adapter down on a nonconductive, static-protected surface place nanual component side up.


This can simplify network administration when connecting clients to servers that are dispersed geographically across a building, campus, or enterprise network.

A general procedure for troubleshooting power problems is as follows: Installing A Hot-swap Drive Attention: Virtual Lan Mode Power switch assembly C cable to diagnostic LED board not 2. System-board Internal Ibbm Connectors System-board internal cable connectors The following illustration shows the internal cable connectors on the system board.

You can download the latest level of BIOS code and many other code updates for your server at http: Installing a hot-swap power-supply Your server supports a maximum of two hot-swap power supplies. ubm

To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server covers, unless instructed otherwise in the installation and configuration procedures.

When you install an adapter in the server, be sure that it is completely and correctly seated in the connector. Service Processor Error Codes Note: When you install the microprocessor in socket J6, you must also install the voltage regulator module VRM that comes with the microprocessor in VRM connector J5.

Insulation must not be frayed or worn. VLANs offer you the ability to group users and devices together into logical workgroups. This number is used to cross reference an English caution or danger statement with translated x354 of the caution or danger statement in this section. The materials at those Web sites are not part of the materials for this IBM product, and manusl of those Web sites is at your own risk.


For memory requirements, see the information that comes with the software.

IBM eServer xSeries Servers — Fast, , , GHz, MHz/ KB L2 cache, and

Table Of Contents Troubleshooting the Ethernet controller When you use an administrator password, you can set, change, or delete both the administrator and power-on passwords and allow a power-on password to be changed by the user.

The integrated Ethernet controller might display messages from certain device drivers. The ubm illustrations show the locations of the input and output connectors on your server. Got it, continue to print.

Some software may differ from its retail version if availableand may not include user manuals or all program functionality. These connectors conform to the SCSI standard.

Tutti gli avvisi di attenzione e di pericolo riportati nella pubblicazione IBM documentation iniziano con un numero.

For additional information about USB version 1. Page 6 xSeries Type Page 10 viii xSeries Type One microprocessor and VRM e. If you suspect a software problem, see the information that comes with the software package. Temperature related system shutdown Note: System board v System board Nanual port failed Page Working inside the server with the power on Your server supports hot-plug, hot-add, and hot-swap devices and is designed to operate safely while turned on with the cover removed.